Product Tips & Tricks

Instructions for Use

DRI WASH 'n GUARD® ULTRA-IONT Waterless CarwashT

Listen to Rod Yanke, the creator of Ultra-Ion™ Waterless Carwash, speak about the reason Ultra-ION™ was developed and the benefits Ultra-Ion™ provides to you, your vehicles, and your home by clicking here. (File Size: 8Mb)

It is extremely important that DRI WASH 'n GUARD® Uitra-Ion™ be applied with a DRI WASH 'n GUARD® AIRosol pump sprayer only. Use on hard, non-porous surfaces only. Pre-test on inconspicuous area before use. Can be used over surface containing moderate level of dust, dirt, road grime or salt.

Refill Procedures:
Unscrew collar nut at neck of AIRosol pump sprayer and remove internal spray mechanism Invert bottle of product, shake vigorously for 15-20 seconds Pour contents into AIRosol pump sprayer until 75% full Re-Install spray mechanism and collar nut

1. Apply DRI WASH 'n GUARD® Uitra-Ion™ in a cool, dry surface in a shaded area for best results. Avoid windy conditions if possible.
2. Use a clean terry cloth towel to apply the product. Use the DWG™ Buffing Towel for buffing.
3. Invert the AIRosol pump sprayer and shake vigorously for 15-20 seconds.
4. Pressurize the bottle by pumping the cap "up and down" until a strong resistance is felt (approx. 10-15 times).
5. Spray a light coat of DRI WASH 'n GUARD® Uitra-Ion™ Waterless Carwash™ on a small section of vehicle (1sq.m.), spraying with a broad sweeping motion where possible.
6. Using the terry cloth towel, with moderately firm pressure, rub polish thoroughly over the sprayed area until the filmy haze that developed almost disappears.
7. Buff the remaining haze to a high gloss with the DWG™ buffing towel

1. Use a conventional or orbital-type buffer equipped with a foam-polishing pad. Do not exceed 1,500 RPM.
2. Apply DRI WASH 'n GUARD® Uitra-Ion™ as described in steps 3, 4, and 5 above.
3. Immediately buff sprayed area to a high gloss.
4. Continue, section by section, until all accessible areas have been buffed.
5. Polish any remaining areas by hand, if necessary. For ultimate surface restoration, use DRI WASH 'n GUARD® OxyGone™ on the surface of the vehicle, and follow with DRI WASH 'n GUARD® Uitra-Ion™ Waterless Carwash™ and Protective Glaze.

Caution: Prevent product from freezing. DO NOT MIX THIS PRODUCT WITH ANY OTHER CHEMICAL OR WATER. First Aid Treatment: If swallowed, call physician or poison control centre immediately.

[Back to Top]

DRI WASH 'n GUARD® OxyGoneT

Directions By Hand:

1. Invert bottle and shake vigorously for 5 seconds
2. Apply a small amount of OxyGone™ on a clean terrycloth towel.
3. Using the towel, work the product into the oxidized surface until haze begins to disappear.
4. Using another clean terry cloth towel, buff the treated surface to a gloss.
5. For best result work in small sections.

For ultimate surface restoration, use DRI WASH 'n GUARD® OxyGone™ on the surface of the vehicle, and follow with DRI WASH 'n GUARD® Ultra-ION™ Waterless Carwash™ and Protective Glaze.

Directions by Machine:

1. Invert bottle and shake vigorously for 5 seconds.
2. To prevent splatter, apply a small amount of OxyGone™ on a clean terrycloth towel and spread over a 30cm area.
3. Buff to a high gloss using a conventional or orbital-type buffer equipped with a foam-polishing pad. Do not exceed 2,400 RPM.

Caution: Use under well ventilated conditions.
Pre-test on inconspicuous area before use.
First Aid Treatment: If swallowed, call physician or poison control centre immediately.

[Back to Top]

DRI WASH 'n GUARD® Premium Metal Polish with exclusive EXP-7T

DO NOT use on thin plated metal surfaces.
DO NOT use near heat, sparks, or flame.
DO NOT breath vapours for extended periods.
DO NOT mix this product with any other chemicals or liquids.

Directions:

1. Use two soft, clean terry cloth towels... one for cleaning/polishing and one for buffing.
2. Invert bottle and shake vigorously before and during use.
3. Apply a small amount of DRI WASH 'n GUARD® Premium Metal Polish on a clean terry cloth towel.
4. Rub surface lightly until polish turns dark.
5. Let dry and buff with a separate clean, terry cloth towel.
6. For maximum protection, apply DRI WASH 'n GUARD® Waterless Car Wash and Protective Glaze after treatment.

Caution: Use under well ventilated conditions.
Pre-test on an inconspicuous area before use.
First Aid Treatment: If swallowed, call physician or poison control centre immediately.

[Back to Top]

DRY WASH 'n GUARD® Upholstery, Fabric & Carpet Treatment with Exclusive PolyGuard-5T

DO NOT use on glass, floors, or painted surfaces.
DO NOT mix this product with any other chemicals or liquids.

Directions:

1. Use one soft, clean terry cloth towel or soft bristle brush for cleaning, and another for drying.
2. Invert bottle and shake once or twice.
3. Spray area to be cleaned from a distance of 30cm.
4. Agitate sprayed area with soft, clean, terry cloth towel or bristle brush.
5. Pat dry with soft, clean, terry cloth towel.
6. Allow area to completely dry.

Caution: Keep out of reach of children.
Pre-test on an inconspicuous area before use.
First Aid Treatment: If swallowed, call physician or poison control centre immediately.

[Back to Top]

DRI WASH 'n GUARD® Leather & Vinyl Treatment with Exclusive PolyGuard-5T

DRI WASH ‘n GUARD® Leather and Vinyl Treatment contains no petroleum distillates, soaps or detergents. It is non-corrosive, non-flammable, and non-caustic.

DO NOT use on glass, floors, woven materials or painted surfaces.
DO NOT mix this product with any other chemicals or liquids.

Directions:

1. Use one soft, clean terry cloth towel or sponge for cleaning, and another for buffing.
   Invert bottle and shake once or twice.
2. Spray area to be cleaned from a distance of 30cm.
3. To prevent over-spray, apply to an area no larger than 25cm.
4. Rub sprayed area with a soft, clean terry cloth towel or sponge. (For excessively soiled areas, scrub lightly with a soft brush and then rub with a clean soft terry cloth towel or sponge.)
5. For the best result buff lightly with a clean, terry-cloth towel.

Caution: Keep out of reach of children.
Pre-test on an inconspicuous area before use.
First Aid Treatment: If swallowed, call physician or poison control centre immediately.

[Back to Top]

DRI WASH 'n GUARD® Tyre & Exterior Trim Treatment with Exclusive PolyGuard-4T

DO NOT use on glass, Plexiglas, mirrors, chrome or other non-porous surfaces.
DO NOT use in an area where painting occurs or on surfaces that may require painting.
DO NOT mix this product with any other chemicals or liquids.

First: Replace shipping cap with trigger sprayer (included).

Directions:

1. Use one soft, clean cloth for cleaning/polishing and another for buffing.
2. Invert bottle and shake once.
3. Rotate nozzle to "SPRAY" position.
4. Spray generously onto surface from a distance of approximately 30cm.
5. Immediately polish the area with a soft, clean cloth. The use of a small, soft bristle brush may be helpful in penetrating rough or uneven surfaces such as tyre sidewalls.
6. Buff to a shine using a second soft, clean cloth.
7. Repeat process for higher lustre and longer lasting protection.

Caution: Keep out of reach of children.
First Aid Treatment: If swallowed, call physician or poison control centre immediately.

[Back to Top]